Fail2Ban is an intrusion prevention framework written in the Python programming language. It works by reading SSH, ProFTP, Apache logs, etc. And uses iptables profiles to block brute-force attempts.
Check for system updates and install them.
apt update -y apt upgrade -y
Command to install the Fail2Ban
apt install fail2ban -y
To enable fail2ban, run the following command.
systemctl enable fail2ban
To check the status of the service, run the following command.
systemctl status fail2ban
root@crown:~# systemctl status fail2ban ● fail2ban.service - Fail2Ban Service Loaded: loaded (/lib/systemd/system/fail2ban.service; enabled; vendor pres> Active: active (running) since Thu 2022-04-07 13:37:13 UTC; 14s ago Docs: man:fail2ban(1) Main PID: 2557 (fail2ban-server) Tasks: 5 (limit: 1034) Memory: 13.2M CPU: 442ms CGroup: /system.slice/fail2ban.service └─2557 /usr/bin/python3 /usr/bin/fail2ban-server -xf start Apr 07 13:37:13 crown systemd: fail2ban.service: Deactivated successfully. Apr 07 13:37:13 crown systemd: Stopped Fail2Ban Service. Apr 07 13:37:13 crown systemd: fail2ban.service: Consumed 3.967s CPU time. Apr 07 13:37:13 crown systemd: Started Fail2Ban Service. Apr 07 13:37:13 crown fail2ban-server: Server ready
Jail.conf contains a section in which Configuration settings can be done for the fail2ban, we are not going to edit this file because package upgrades can overwrite this file.
Jail.local contains the same sections where "jail.conf" file contains and it can override these values.
Command to create a jail.local configuration file by copying the default jail.conf file.
Open file to configure.
Find the following line in the config file
/etc/fail2ban/jail.local and uncomment it to whitelist the IP address.
#ignoreip = 127.0.0.1/8 ::1
Once you uncomment it, add your IP address at the last of the command For ex.
ignoreip = 192.168.0.100 192.168.1.0/24
Multiple IP address can be whitelisted with the above configuration, they have to be separated with a single white space. You can also white list an IP block as shown above.
3 main options in these settings,
- bantime: is the number of sec/hours/day that an IP address is banned.
- findtime: is the window that fail2ban will pay attention to when looking for repeated failed authentication attempts.
- maxretry: is the maximum try which will be given before blocking.
Find these lines in the config file /etc/fail2ban/jail.local and change as you required.
Default values of the option are,
bantime = 10m findtime = 10m maxretry = 5
Note: If you want to block IP address permanently use a negative value in the bantime option.
Note: To receive email alerts, you need to have an SMTP installed on your server.
To receive email alerts with relevant logs, find the following line in the config file /etc/fail2ban/jail.local and make sure that the following line is present.
# ban & send an e-mail with whois report and relevant log lines # to the destemail. action_mwl = %(action_)s %(mta)s-whois-lines[sender="%(sender)s", dest="%(destemail)s", logpath="%(logpath)s", chain="%(chain)s"]
To configure sending and receiving email addresses.
Find the following line in the config file /etc/fail2ban/jail.local and update the details.
destemail = firstname.lastname@example.org sender = email@example.com
To interact with the Fail2ban service there is a command-line tool called fail2ban-client.
To check its available options enter the following command.
Here is a few examples that can be performed by using this tool,
Check the jail status.
fail2ban-client status sshd
To unban an IP.
fail2ban-client set sshd unbanip "IP address here"
To Ban an IP.
fail2ban-client set sshd banip "IP address here"